ZS型不锈钢卧式单级离心泵

引言

    ZS型不锈钢卧式单级离心泵采用不锈钢板冲压胀型焊接等先进工艺制成，是国内首创的新一代离心泵，可替代传统的IS泵和一般的耐腐蚀泵。其具有外形美观、结构轻巧、高效节能、经久耐用和耐轻腐蚀、低噪音等特点。

型号含义

Z    S    65 —50 — 200 — 11.0
│  │  │     │       │         └─ 电机功率（kW）
│  │  │     │       └────叶轮名义直径（mm）    
│  │  │     └────── 排出口直径（mm）
│  │  └────────吸入口直径（mm）
│  └───────── 加长轴（mm）
└────────── 不锈钢卧式单级离心泵

应用

ZS型不锈钢卧式单级离心泵是一种适应范围较广的多功能产品，可以输送各种包括水或工业液体在内的不同介质，适用于不同温度、流量和压力范围。其典型应用主要包括以下方面：
l         供水：水厂过滤、输送及分区送水和主管增压；
l         工业增压：流程水系统、清洗系统；
l         工业液体输送：锅炉给水、冷凝系统、冷却和空调系统、机床配套、酸碱输送；
l         水处理：蒸馏系统或分离器、游泳池等；
l         农田灌溉、石油化工、医药卫生等。

安装条件

ZS型不锈钢卧式单级离心泵为泵轴直联型联结，由泵、泵轴和标准电机组成：
1）泵应安装在通风且防冰冻的地方；
2）泵的安装要保证在使用时泵不受系统管路的张力影响；
3）如果泵安装在户外，必须配置合适的外罩以防止电气元件进水或凝露；
4）为了方便于检查和维修，在机组的周围应必须留有足够的空间；
5）电气接线装置应保证泵不受缺相、电压不稳、漏电和过载的损害；
6）泵应水平安装在基座上，水平方向为泵的吸入口，垂直方向为泵的排出口。

运行条件

l         清洁、稀薄、非易燃易爆并不含有固体颗粒和纤维的液体；
l         温度在-20℃至+100℃之间的液体；
l         环境温度*高+40℃；
l         *高海拔1000米；
l         系统*高压力10bar。

电机

l         电机为全封闭、风冷式二极标准电机；
l         防护等级：IP55；
l         绝缘等级：F；
l         标准电压：50Hz 1×220V
                       3×380V

性能参数

Introduction ZS Stainless steel horizontal single-stage centrifugal pump is made by advanced techniques such as pressing bulging welling of corrosion resistant plate. It is a new generation centrifugal pump initiated in and may replace traditional IS pump and common corrosion proof pump. It features beautiful appearance, light and handy structure, high efficiency and energy saving, durable, corrosion proof, low noise, etc. Connotation of the type Z    S   65 —50 — 200 — 11.0 │  │  │    │      │        └─Motor Power（kW） │  │  │    │      └─── Nominal diameter of impeller（mm） │  │  │    └──────Diameter of discharge port（mm） │  │  └────────Diameter of suction port（mm） │  └─────────stub shaft（mm） └────────── stainless steel horizontal single-stage centrifugal pump Application ZS Stainless steel horizontal single-stage centrifugal pump is a sort of multifunction product with wide application. It may transmit various mediums including water or industrial liquid and is suitable for different temperature, flow rate and range of pressure. Its typical application mainly in codes the following aspects： l Water supply: filtration in water works, transportation and subarea water carriage, pressurization of main duct; l Industrial pressurization: flow wetting system, cleaning system; l Transportation of industrial liquid: water supply of boiler, condensed system, cooling and air-conditioning system, machine tool support, acid and alkali transportation; l Water treatment: distilled water system or separator, swimming pool, etc.; l Irrigation of agricultural land, petrochemical industry, medicine and sanitation, etc. Installation requirements ZS Stainless steel horizontal single-stage centrifugal pump is the direct connection by pump shaft ,composed of pump ,pump shaft and standard motor: 1) The pump shall be installed on the ventilating and anti-freezing place; 2) The installation of the pump shall ensure that the pump will not be influenced by the tension of pipeline; 3) If the pump is installed outdoor ,suitable outer cover must be configured to prevent electric elements from water inflow or coagulating dew; 4) To facilitate in section and maintenance ,enough space must be left around the machine group ; 5) Electric wiring device shall guarantee that the pump will not be damaged by lack of phase ,unstable voltage ,current leakage and overload ; 6) The pump shall be installed on the pedestal horizontally .Horizontal direction is the suction port for the pump ,and vertical direction is the discharge port for the pump . Operating condition l Clean, thin, non-flammable and explosive, not containing the liquid with solid particle and fibre; l Liquid temperature -20℃/ +100℃； l Ambient temperature: up to+40℃； l Altitude: up to 1000m； l Max. pressure of the system is 10bar. Motor l TEFC motor,2-pole； l Protection class:IP55； l Insulation class: F； l Standard voltage：50Hz 1×220V 3 ×380V

企业名片